Water CareNovember 14, 2026· 3 min read

How to Balance Hot Tub Water (In the Right Order)

A plain-English guide to testing and balancing spa water: what each reading means, the order to adjust things, and the weekly routine that keeps water clear.

Draft for Eddy's review. Visible on the preview; set draft: false in the post's frontmatter once approved.
Testing and balancing spa water, start to finishVideo coming soon

Most “my water is cloudy / foamy / smells weird” questions come back to the same thing: the water isn’t balanced, or it’s balanced in the wrong order. Here’s the simple version I walk customers through.

Always read the label. Dosing depends on your tub’s water volume and the specific product. Follow your manufacturer’s manual and the chemical instructions, and never mix chemicals together.

What you’re testing for

Use fresh test strips or a liquid test kit. These are the readings that matter most, along with the ranges commonly recommended for hot tubs. Your tub’s manual may list slightly different targets; go with the manual.

Reading What it does Common target range
Total alkalinity (TA) Buffers pH so it doesn’t swing around about 80–120 ppm
pH How acidic or basic the water is; affects comfort and how well sanitizer works about 7.2–7.8
Calcium hardness Too low can be corrosive; too high can cause scale follow your manual (often in the low hundreds of ppm)
Sanitizer Kills bacteria follow your sanitizer’s label and your manual

The order matters

Adjusting things in the wrong order is how people end up chasing their tail for a week.

1. Alkalinity first

Alkalinity acts like a buffer for pH. If it’s off, pH won’t stay put no matter what you add.

  • Low TA: add an alkalinity increaser per the label.
  • High TA: a pH decreaser will bring it down over time.

Run the jets with the cover off, wait the time the label recommends, and retest.

2. Then pH

Once alkalinity is in range, fine-tune pH with pH increaser or decreaser. Small doses, wait, retest. It’s easy to overshoot.

3. Then calcium hardness

Check it when you fill the tub and every so often after. Fill water varies a lot by area. If you have hard water, ask about a stain and scale product or a pre-filter for your hose.

4. Then sanitizer

With the water balanced, your sanitizer can do its job. Keep a steady level per your sanitizer’s label rather than letting it spike and crash.

5. Shock after heavy use

“Shocking” oxidizes the stuff that builds up from bathers (sweat, lotions, etc.). Shock per the label, typically weekly and after a lot of use. Leave the cover open for the time the product recommends.

A simple weekly routine

  1. Test the water two or three times a week (more when the tub sees heavy use).
  2. Adjust in order: alkalinity, pH, then sanitizer.
  3. Shock weekly and after parties.
  4. Rinse the filters with a hose regularly, and give them a proper filter-cleaner soak periodically.
  5. Check the water level; low water can cause pump and heater problems.

Bigger picture maintenance

  • Drain and refill every few months, depending on use and your manufacturer’s guidance. Water eventually gets “used up” no matter how well you balance it.
  • Replace filters when they’re worn, torn or won’t come clean.
  • Wipe the waterline and clean the cover underside.

Common water problems

  • Cloudy water: often low sanitizer, a dirty filter, or high pH/TA. Check filters first, then balance and shock.
  • Foam: usually soaps, lotions or detergent residue from swimsuits. A defoamer is a quick fix, but a drain and refill is often the real fix.
  • Strong chemical smell / itchy eyes: usually means the water needs to be shocked, not that there’s too much chlorine.
  • Scale on surfaces: often high calcium or high pH.

Have a water problem you can’t solve? Post your readings on the question board along with your tub’s brand and model, and I’ll take a look.

#water-chemistry#ph#alkalinity#sanitizer#routine

Still stuck?

Ask about your exact brand and model on the question board.

Ask Eddy →